Thứ Ba, 29 tháng 4, 2014

High voltage of transformers


I'm looking for a possible simple circuit as I cannot control to a transformer that I can use it as a source of high voltage. The circuit with the E is already quite great shocker but you need 2 windings. There is a circuit where I can make something out of 1 Prim Wicklumg? Get the ignition coil Zer hacker circuit from the MK side which should be quite well funzen. have I tried with nem mormalen Printtrafo! But not much is here! I think a small transformer from a disposable camera would be better suited. You need in any case any switching element so a normal bipolar transistor or a HV electrical .
 
This is the most important thing is to Netzteiltopologien to see it in principle. Voltage-guided operating mode, it is possible that the primary current is running or that just the core saturates. Up to half - / Vollbrückentopologien a Lück end power curve is used, however, the power-run push-pull converters can exploit the full hysteresis loop of the core. You can implement Flyback and forward converters as one transistor circuits, and both need no further taps. Sure they work but also not resonant and significant switching losses occur at larger scales of power.

The rectifier secondary only consists of a simple diode, a bridge driver has some advantages over the other topologies, especially services targeted by you.

I can advertise for Flybackwandler HV MOSFETs with good suppressor from personal experience.

Thứ Năm, 24 tháng 4, 2014

E - shocker of doom!



I take my HV electrical  (BUZ341, 2 x 0, 33µF FKP1.) So, transformer core an EE70 - with 1 + 1Wdg. 6 mm² silver - LS - cable as a primary winding. Then three layers to 2cm each winding width 0, 4 mm CuL. Behind a 7 - stage cascade from WIMA FKP1 comes with each 47nF / 2kV. So I have to go on at 12V > = 10kV come. Behind this is a MMC from 2 x 3 MOcaps. (Each 3 in number, of which 2 strands parallel)
Do you think doing here, or working at all?
(No, I want to shock so that no living being as well! I could use but still some kV with good peak power...)

The 12V - supply lines (1, 5 mm²) are in the arcen @ 12Vin from a 45Ah shipments after 2 LiBos by per 1 sec already soft...The output voltage is 900Veff.
The ZVS so should have enough steam

Schade, also as fast cooking of Kühli, that really makes mood to Palanka...

€dit: My pliers - A - meter says ca 40A when the arc Burns! : shock:
That's according to my calculation ca 450W. At 12V, packs a punch...
I should not take more V, otherwise I have dead Moses... MOCs are unsuitable.You may not discharge at high currents!But else very interresting. Ölpapierkondis, is there already a little humbling...
Clearly I should run no Tesla so but DC should be OK. Today arrive my diode, if fit, continue today evening. this device can kill! and besides, it's a heavy useless bunch of crap, which you can't place into your pocket.

MOT stack


I'm back from the last gathering orgy and purchased random 6 identical MOT's MOC's and MOD's.

My 1st was Iddee ~ Motstack. or someone has a better Iddee?
or has someone to connect them the b essere idea as so:testing jobs
Of course per MOT and outer conductor comes a secondary kurzeschlossener and grounded MOT as a current limitation in and the cores of the MOT's to be grounded.

Also I would point out on it that I'm in the clear, what I'm doing and that each contact or anderwertiges in contact come with high-voltage lebendgefährlich and is lethal in this case. I am a trained electrician familiar with the matter and know what I'm doing. * censored by codered * who did: oops: I'm so obsessed with safety or smart-scheisserisch or about both? you said that now but nice, thank you very much for the support, axxxel. My day is saved. Here I must agree with axxel you bisd neither possessed nor smart scheisserisch! You think with only and you know vlt. inexperienced out there, that if you ned Aufpassn pain can add up! And ds is good thing.
Not provocative should work. I apologize if I you too close stepped on it.

Randy you a better idea than my circuit kV? Construction could be so your secondary CAP and diode man determined to a full rectification
to forge, only I know even just doesn't like :D
or maybe all 3 together bring in resonance (if you so want Palanka: moep:)